Concave-beam Low-bed Semi-trailer
video
Concave-beam Low-bed Semi-trailer

Concave-beam Low-bed Semi-trailer

Designed with a sunken center deck, this concave-beam low-bed semi-trailer lowers overall loading height to move tall machinery—such as excavators, bulldozers, and wheel loaders—under overhead bridge and clearance limits.

Product Introduction

Designed with a sunken center deck, this concave-beam low-bed semi-trailer lowers overall loading height to move tall machinery-such as excavators, bulldozers, and wheel loaders-under overhead bridge and clearance limits.

 

Payload & Loading Ramp Specifications

 

Product Parameters

Technical Specifications

Payload Capacity

40T (2-axle), 60T (3-axle), 80T (4-axle), 100T (custom multi-axle)

Ramp Configuration

Standard mechanical spring-assisted ramps; optional double-acting hydraulic foldable ramps

Ramp Dimensions

2,200–3,000 mm length × 750 mm width per side

Ramp Load Rating

Up to 15T static design-rated capacity per single ramp

Loading Angle

12°–16° relative to ground level

Hydraulic System

16 MPa (160 bar) working pressure; onboard electro-hydraulic unit

Ramp Safety

Anti-slip steel traction bars and mechanical locking pins

 

Axle, Coupling & Braking

 

Product Parameters

Technical Specifications

Axle Configuration

2-axle, 3-axle, or 4-axle; 13T, 16T, or 20T rated axle units

Axle Brands

FUWA or BPW

Suspension

Standard mechanical leaf spring; optional air suspension

Tire Options

11.00R20, 12.00R20; optional 235/75R17.5 for specified low-deck builds

Steering & Lift Axles

Optional self-steering rear axles or front hydraulic lift axles

Tractor Compatibility

6×4 or 8×4 tractors; recommended 380–540 HP

Coupling & Landing Gear

2-inch or 3.5-inch kingpin; 1,250–1,400 mm fifth-wheel height; 28T lifting / 50T static landing gear

Braking & Electrical

Dual-line air brakes, WABCO or Knorr-Bremse 4S/2M ABS, T30/30 chambers, 24V lighting system

 

Concave Beam Design

 

Concave Beam Structure: Sunken center platform positioned between the gooseneck and rear axle group drops loading height for high-cube heavy loads.

 

Equipment Compatibility: Built for crawler and wheeled machinery, including hydraulic excavators, bulldozers, wheel loaders, and road rollers.

 

Low Center of Gravity: Lowered platform height reduces total haul profile and improves vehicle stability compared to standard flat decks.

 

Gooseneck Options: Available in fixed gooseneck designs for rear-ramp loading or detachable goosenecks for front-level drive-on equipment loading.

 

Main Beam Structure

 

Main Beam Layout: Twin longitudinal I-beams with integrated cross-members deliver high torsional resistance under concentrated off-center loads.

 

Steel Selection: High-strength Q355B steel is used for standard 40T–60T frames, while Q690D high-yield steel powers heavy-duty 80T–100T builds, backed by Mill Test Certificates (MTC).

 

Beam Profiles: Web heights range from 450 mm to 550 mm (8 mm–14 mm thick), paired with top flanges (14 mm–20 mm) and bottom flanges (16 mm–22 mm) scaled to payload capacity.

 

Automated Welding: Longitudinal main beam flange-to-web joints are joined via continuous automatic submerged arc welding (SAW) on primary load sections.

 

Loading Dimensions

 

Main Deck Dimensions: Standard main deck lengths range from 13 m to 17.5 m with a 3,000 mm base width, featuring optional manual or hydraulic side-extension brackets.

 

Platform Height: Base unladen deck height sits between 700 mm and 800 mm; full-load height settles 50 mm to 80 mm lower under suspension and tire deflection.

 

Load Distribution: Kingpin position and axle spacing distribute payload weight across the tractor fifth wheel and trailer axle group.

 

Quality Inspection

 

Weld Inspection & UT: Primary frame joints undergo 100% visual inspection; main load-bearing T-joints undergo Ultrasonic Testing (UT) per internal UT procedures, benchmarked against ISO 5817 weld defect standards.

 

Surface Blasting: Assembled chassis undergo automatic shot blasting to Sa 2½ surface cleanliness per ISO 8501-1 to strip mill scale and rust.

 

Coating System: Applied with an epoxy zinc-rich primer and polyurethane topcoat, reaching a total Dry Film Thickness (DFT) of 120 µm to 140 µm.

 

Pre-Delivery Testing: Every completed trailer undergoes axle alignment checks, air brake pressure tests, and electrical circuit validation before dispatch.

 

Production Process

 

Factory Showcase

 

Packaging & Transportation

 

FAQ

 

Q: Is the concave-beam design right for our equipment, or should we choose a flat-deck trailer?

A: Choose the concave-beam design when your cargo is tall and must clear bridges or overhead limits. If your loads are low-profile or very wide, a flat-deck model may be more cost-effective.

Q: Which axle configuration is right for our heaviest load?

A: Choose the 2-axle for light machinery, the 3-axle for mid-size excavators and loaders, and the 4-axle for heavy equipment. Share your heaviest machine and local axle limits, and we will recommend the best fit.

Q: Is the trailer compatible with our existing tractor?

A: Please share your tractor model, fifth-wheel capacity, and kingpin size, and our engineers will confirm compatibility before production.

Q: Can the trailer be adapted to our local road regulations?

A: Yes. We can adjust axle spacing, overall dimensions, reflective markings, rear underrun bars, and lighting packages, quoted separately. Please share your national requirements before ordering.

Q: Can we inspect the trailer before shipment?

A: Yes. You or your appointed third party (SGS, BV, or TÜV) may inspect the trailer at our factory and witness a braking and functional test before release.

Q: What warranty do you provide?

A: We offer a 12-month warranty from the Bill of Lading date, covering main beam welds against cracking under normal rated use. Tires, brake linings, and damage from overloading are excluded.

Q: What are the MOQ and standard lead time?

A: MOQ is 1 unit. Standard lead time is 25 to 35 days from deposit confirmation and drawing approval, depending on axle configuration and customization.

Q: Can the trailer be shipped in a way that reduces freight cost?

A: Yes. The detachable gooseneck and ramps can be separated to meet the dimensional limits of Ro-Ro or flat-rack shipping, helping lower per-unit freight cost.

Hot Tags: concave-beam low-bed semi-trailer, China concave-beam low-bed semi-trailer manufacturers, suppliers, factory, Detachable Low bed Semi trailer, Extendable Low bed Semi trailer, Fixed Low bed Semi trailer, Flat deck Low bed Semi trailer, Heavy duty Low bed Semi trailer, Lightweight Low bed Semi trailer

You Might Also Like

(0/10)

clearall